These are the instructions to install the IFace interface inside of the Icom IC-706MKIIG. The installation is very easy.
The IC-706MKIIG, like other radios, has a fairly complex configuration and uses two different intermediate frequencies. We are interested in the first, the “wideband” one, the one before the main bandpass filter (the roofing filter so to speak). The sequence of operations to be performed in order to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency is shown below. The intermediate frequency filter is also used in transmission, so it will be preferable to use the PTT command to disable the IFace during transmission. The following images show the point where the IF signal will be taken.
Let’s start by analyzing the wiring diagram. We have to find the first mixer, the PTT and where to take the power supply. From the following images everything will appear clear.
PTT and power supply can be easily taken from the connector J10. The interesting signal are labeled as T8 and 13.8 respectively.
At this point we have to locate the points where we connect the electric cables to the IFace. The following images show where to take the various signals.
If you like the idea and the goodness of the proposal buy an IFace using the button below.
ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.
For more information do not hesitate to write us. Have fun!
These are the instructions to install the IFace interface inside of the Kenwood TS-450S/690S. The installation is very easy.
The TS-450S/690S, like other radios, has a fairly complex configuration and uses different intermediate frequencies. We are interested in the first, the “wide band” one, the one before the main band pass filter (the roofing filter so to speak). The sequence of operations to be performed in order to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency is shown below. The signal path for TX and RX are fairly separated, so to use the PTT command to disable the IFace during transmission is not required. The following images show the point where the IF signal will be taken.
Let’s start by analyzing the wiring diagram. We have to find the first mixer and where to take the power supply. From the following image everything will appear clear.
At this point we have to locate the points where we connect the electric cables to the IFace. The following image shows where to take the various signals.
This last image shows the RF UNIT and where the IFace interface is to be connected.
If you like the idea and the goodness of the proposal buy an IFace using the button below.
ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.
For more information do not hesitate to write us. Have fun!
These are the instructions to install the IFace interface inside of the Icom IC-706. The installation is very easy.
The IC-706, like other radios, has a fairly complex configuration and uses two different intermediate frequencies. We are interested in the first, the “wide band” one, the one before the main band pass filter (the roofing filter so to speak). The sequence of operations to be performed in order to obtain a sufficient bandwidth to realize a panoramic receiver around the chosen IF frequency is shown below. The intermediate frequency filter is also used in transmission, so it will be preferable to use the PTT command to disable the IFace during transmission. The following images show the point where the IF signal will be taken.
Let’s start by analyzing the wiring diagram. We have to find the first mixer, the PTT and where to take the power supply. From the following images everything will appear clear.
PTT and power supply can be easily taken from the connector J10. The interesting signal are labeled as T8 and 13.8 respectively.
At this point we have to locate the points where we connect the electric cables to the IFace. The following images show where to take the various signals.
This last image shows the inside of the RTX and where the IFace interface is to be placed.
If you like the idea and the goodness of the proposal buy an IFace using the button below.
ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.
For more information do not hesitate to write us. Have fun!
Follow the steps below to install the IFace card in the YAESU FT-817. Installation is really very easy.
As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal. We use the first because it is not filtered, i.e. the band is still wide. The following images make it very clear where this point is located. The PTT may not be necessary, the TX and RX circuits are well separated.
The power supply can be taken from the test point TP1084.
At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.
If you are convinced of the goodness of the proposal buy an IFace using the button below.
WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.
For more information do not exist to write to us. Have fun!
Follow the steps below to install the IFace card in the YAESU FT-991. Installation is really very easy.
As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal. We use the first because it is not filtered, i.e. the band is still wide. The following images make it very clear where this point is located. The PTT may not be necessary, the TX and RX circuits are well separated. The power supply can be taken from the TP1034 near the J1018 connector.
At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.
If you are convinced of the goodness of the proposal buy an IFace using the button below.
WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.
For more information do not exist to write to us.
Have fun!
Follow the steps below to install the IFace card in the ICOM IC-R72. Installation is really very easy.
As always we start from the block diagram and try to find information on where to get the first intermediate frequency signal: we take the first because it is not filtered and the band is still wide. The following images make it very clear where this point is located (on resistance R82). Being a receiver, there is no need to look for the PTT signal. The power supply can be taken between the inductance L66 and the resistance R68.
At this point all that remains is to identify the points on the PCB where to take the signals: refer to the following images.
Finally, this photo suggests where to place the IFace card and where to get the signals.
If you are convinced of the goodness of the proposal buy an IFace using the button below.
WARNING: Although the installation of IFace is not difficult, it is done at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side effects or anything else.
For more information do not exist to write to us.
Have fun!
Our client Alberto IK0ZTL just sent us a nice testimonial on how he used our IFace card to add an SDR receiver to his nice TS-2000.
He did a great job by inserting everything into the radio, including the RTL-SDR converter, so that he only had the USB cable out to connect to the computer.
Find all the nice work described in a PDF to download right below.
Would you like to have a radio with a nice 40 “LCD display where you can view spectrograms, waterfalls and much more information? And what would you say to have a modern SDR radio so that you can listen to more signals at the same time? Wouldn’t it be nice to have many digital filters to improve reception during contest or DX activity? If you answered yes then IFace is the electronic card that allows you to have all of this without having to buy a new radio. How? By inserting it inside your “old” beloved RTX and using a cheap SDR receiver for computers (some suggestions here) such as an USB RTL-SDR dongles.
Don’t you think so? Please watch this video and then keep reading.
The idea behind this product is to continue to use the radio that we have purchased and which has already given us so much satisfaction. Surely we already have the CAT interface with which we control it from the LOG or from other programs and we also have the audio interface for the digital modes. But sometimes we realize that we would need a second receiver (for example to follow the +5 kHz or + 10 kHz of a DX station), band filters with steeper sides to eliminate a disturbance on an adjacent frequency or a notch because our radio does not have it or it is not automatic. All this can be a memory!
So suppose to send the intermediate frequency signal (IF) of our radio to a dedicated SDR receiver and to start a program such as HDSDR (or SDR #, SDR Console …). On the screen of our computer we would have the spectrum display around the IF of our radio and, not to be neglected, we could also demodulate what it is receiving. But we could do even more, we could also demoulate other signals that are above or below the frequency tuned by our RTX. Not bad, right? The image below shows a screenshot of HDSDR connected to an FT-450D via an RTL-SDR and the IFace.
Reception at the IF frequency of a FT-450D though the IFace and a RTL-SDR.
What needs to be done is very simple. Let’s start by identifying within our radio the point where to take the medium frequency signal. This is between the output of the first mixer and the subsequent bandpass filters as shown in the following image.
During the reception the difference is strong, listen here.
In order to not alter the operation of our receiver, we must pick up the signal without charging the mixer, i.e. without taking power. For this reason we have to insert a special card between this and the external receiver: we can not connect it directly. The IF signal pick up card, the IFace, creates a copy of the signal to be sent to the external SDR receiver. This is a wideband and no-tune buffer, i.e. no calibration is needed, it is installed and it is ready to work. The usefulness of this circuit is to allow the medium frequency signal to be replicated without increasing the load seen by the source (the mixer) and therefore without changing its performance.
Once the IF signal has been obtained, it is sufficient to connect the A / D converter (an RTL-SDR is already more than enough) to the USB port and start the software for the reception (ex HDSDR, SDR #, SDR Console etc) and our RTX will now be equipped with a nice panoramic receiver.
Are you already convinced? Very well, buy an IFace immediately by clicking on the buttons below!
There are numerous advantages in picking up the IF signal and not the one coming directly from the antenna: one of these is surely the fact that the amplitude of the signal is controlled through the AGC circuitry of the reception stages. This helps to prevent saturation of the dynamics of RTL-SDR (which is not known to be the most extensive). The point where you take the IF signal is easy to find, just take the schematic diagram of your radio and look for the first mixer: at its output you will find the signal of interest. The image below shows the point where you have to connect the IFace interface in the case of a Kenwood TS-530s, a radio of a few decades ago, which can be easily updated with this interface.
The connection to the chosen point can be made with a thin coaxial cable (type RG178 or RG316) and will terminate at the “Input” pad of the IFace. If the connection is very short, a coaxial cable may not be necessary. The “Output” instead will be connected with another small coaxial cable to the input of the chosen SDR receiver. Obviously the buffer must be powered: it will not be difficult to find inside the radio a point where to draw a voltage of 9 Vdc or 12 Vdc. The following images show how easy it is to install the IFace into the TS-530s.
Sampling point of the IF signal
IFace inside a TS-530s
IF output connector
Powering the IFace with 12 Vdc from the radio (red wire)
Running IFace
After making these simple wiring, you can connect your SDR receiver and start the reception software. The following image shows the SDR# screen during the reception with a Kenwood TS-530s (its intermediate frequency is 8.83 MHz) and an economical RTL-SDR.
Another IFace has been installed in a YAESU FT-450D. As you will see from the photos, the space occupied is very little and the time required to connect the 4 conductors (+13 V, Gnd, Ptt +, IF) is a few minutes. In this case the Ptt signal was used, that is the “TX” signal present in the IF-UNIT of the radio. All this clearly appears in the following images.
The main characteristics of the IFace are:
power supply: 8-15 Vdc, I <50 mA
bandwidth: > 700 MHz
input impedance: > 500 kOhm
output impedance: 50 Ohm
power-down input ( PTT)
dimensions: 38 x 48 mm
In case you do not want to display any signal during transmission it is possible to turn off, by sending it into power down, the buffer of the IFace through a special input pin (PTT) as shown in the following picture. To be more accurate, an active high PTT, i.e. the signal is at a voltage > 5 V when transmitting, otherwise 0 V, or an active low PTT, i.e. the signal is at 0 V when the radio is transmitting, otherwise it must be floating, can be used.
The following video shows how the card reacts to the pressure of the PTT, that is when the radio changes from reception to transmission: the red LED indicates that the card is in power-down because the radio is transmitting.
If you were still not convinced of the goodness of this interface look at this other video where you can see how the IFace works when added to an old Kenwood TS-530s.
Do you have any questions? Maybe we already have the answer you’re looking for.
The price of IFace is only € 42.90 including VAT + shipments costs for the “IFace + Cables” kit. If you also want SMA coaxial connectors, those for power supply and those for the PTT buy the “IFace + Connectors + Cables” kit for only € 54.90 VAT + shipping costs.
There’s a third option, “IFace + Connectors + SDR Panadapter”. This comprises a powerful 12 bit/sa 10 MHz panadapter that will bring your receiving experience to another level. And it is compatible with the RSP1 from SDRplay: you can use the software SDRuno. This kit costs only €104.90 + shipment.
In this page you can find thelist of the instructions to install the IFace into your radio: it is continuoursly growing. For those radios that are not included yet, send a request so that it can be entered as soon as possible.
Content of the delivery “IFace + Cables”:
one IFace board
1 SMA-m coaxial connector
a coaxial cable with both an SMA-f panel connector and an SMA-m connector in order to connect the IFace to the SDR receiver
four wires to connect the board to the PTT, IF, and powering points on the radio (colors of the wires may be subject to change).
Content of the delivery “IFace + Cables”:
one IFace board
1 SMA-m coaxial connector
a coaxial cable with both an SMA-f panel connector and an SMA-m connector in order to connect the IFace to the SDR receiver
four wires to connect the board to the PTT, IF, and powering points on the radio (colors of the wires may be subject to change)
2 SMA connector for PCB edge mount
2.54 mm pitch connectors for power and PTT
Order now by clicking on the following buttons and have fun.
ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.
Any question? Please use the following form.
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish.AcceptRead More
Privacy & Cookies Policy
Privacy Overview
This website uses cookies to improve your experience while you navigate through the website. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may affect your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
NEWS July 18, 2024 A Telegram group is now available through which you can interact to get faster responses from other customers or, if necessary, from TSP Srl.
Sign up for free by clicking here: Telegram TSP Customers.
Please limit the use of contact forms to send generic requests, they have low reading priority because they are often used to send spam.
NOVITA' 18 Luglio 2024
E' da oggi disponibile un gruppo Telegram tramite il quale interagire per avere risposte più veloci da altri clienti o, in caso, da TSP Srl.
Iscrivetevi gratuitamente facendo click qui: Telegram Clienti TSP.
Per favore limitare l'utilizzo dei form di contatto per inviare richieste generiche, hanno bassa priorità di lettura perché spesso usati per inviare spam.
