Tag sdr

Our buffer interface named IFace can be used to add an SDR panadapter to the Yaesu IC-718.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers and we are interested in the first IF frequency (this makes it easier to operate the panadapter). The IF frequency chosen is 64.455 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following image shows the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required because RX and TX signals are separated.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the Icom IC-R8500.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers with complex architecture. We are interested in the second IF frequency (this makes it easier to operate the panadapter). The IF frequency chosen is 10.7 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following image shows the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required because this radio is a receiver.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the Yaesu FT-890.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers and we are interested in the first IF frequency (this makes it easier to operate the panadapter). The IF frequency chosen is 70.455 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following image shows the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required because RX and TX signals are separated.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the Icom IC-745.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers and we are interested in the first IF frequency (this makes it easier to operate the panadapter). The IF frequency chosen is 70.4515 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following image shows the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal, the PTT+ and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is required because RX and TX signals are not completely separated.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the Kenwood RZ-1.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers and we are interested in a common IF frequency among them (this makes it easier to operate the panadapter). The chosen IF frequency is 45.75 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following image shows the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required, it’s a receiver.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the President Jackson.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses one mixer only for the receptio. The IF frequency is 10.7 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following images show the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required, RX and TX signals are separated.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the Icom IC-7200.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers and we are interested in a common IF frequency among them (this makes it easier to operate the panadapter). The IF frequency chosen is 64.455 MHz and our SDR panadapter will be tuned to this. The following image shows the block diagram of the radio and where to get the IF signal.

The following image shows the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required, RX and TX signals are separated.

In order to buy an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!

Our buffer interface named IFace can be used to add an SDR panadapter to the Yaesu FT-847.

The operations to be carried out are very simple, it is sufficient to obtain from its wiring diagram the information on the points where the IF signal has to be taken. This radio uses several mixers and we are interested in a common IF frequency. This radio uses several mixers and we are interested in a common IF frequency among them (this makes it easier to operate the panadapter). The IF frequency chosen is 45.705 MHz and our SDR panadapter will be tuned to this. The following images show the block diagram of the radio and where to get the IF signal.

The following images show the portions of the schematic diagram of the IF UNIT where we can see the exact points where to sample the IF signal and the power supply.

We now proceed to identify the exact points on the printed circuit board where to take the IF signal to be sent to the IFace. The following images show the sampling point for the IF signal and for the power supply for the buffer interface.

The use of PTT signal is not required, RX and TX signals are separated.

In order to purchase an IFace use the buttons below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information, do not hesitate to write to us using the form below.
Have fun!