Radio accessories Archivi - Page 6 of 6

November 16, 2019

Panadapter SDR for the TS-430s

By admin in Radio accessories Tag kenwood, panadapter, rtl-sdr, sdrplay, sdr, ts-430s

To install the IFa c e card inside the Kenwood TS-430s follow the steps below.

The TS-430s, like other radios, has a fairly complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main bandpass filter. The sequence of operations to be performed to obtain a bandwidth sufficient to realize a panoramic receiver around the chosen IF frequency (48.055 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission may not be necessary. The following images show the point where the IF signal will be taken and the power supply.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the RF UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

September 3, 2019

Panadapter SDR for the IC-735

By admin in Radio accessories Tag ic-735, icom, panadapter, rtl-sdr, sdrplay, sdr

To install the IFace card inside the ICOM IC-735 follow the steps below.

The IC-735, like other radios, has a fairly complex configuration and uses different intermediate frequencies. We are interested in having a “wide band” signal, so it will have to be picked up before the main band pass filter. The sequence of operations to be performed to obtain a bandwidth sufficient to realize a panoramic receiver around the chosen IF frequency (70.451 MHz) is shown below. The path of the TX and RX signals is partly separate, so the PTT command to disable the IFace during transmission may not be necessary. The following images show the point where the IF signal will be taken and the power supply.

Now we need to locate the points where to connect the electric cables to the IFace. The following images illustrate where to get the various signals on the MAIN UNIT.

If you like the idea and the goodness of the proposal buy an IFace using the button below.

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

For more information do not hesitate to write us.
Have fun!

June 21, 2019

Microcontrollor for ARDF beacon

By admin in Products, Radio accessories

This short acticle refers to another article you can find at this address: https://iz0abd.wordpress.com/2019/05/28/beacon-ardf-a-433-92-mhz/

Those who wish to purchase the PIC12F509 microcontroller already programmed to periodically generate an “S” in Morse code can do so through the button shown below.

For any other detail please visit https://iz0abd.wordpress.com/2019/05/28/beacon-ardf-a-433-92-mhz/ or simply send us your request using the form in the contacts section.

Enjoy

January 29, 2019

Instructions to install the IFace

By admin in Radio accessories, RF Tag panadapter, sdr

Here below you can find links to the articles that describe how to modify your radios to insert an IFace interface into them.

For those radios that are not included yet, please send a request so that they can be entered as soon as possible.

ICOM	KENWOOD	YAESU
IC-PCR100 IC-PCR1000	RZ-1	FRG 100
IC-705	TR-751A/E
IC-706	TS-50s	FT-102 – Use IF OUT-2 on rear RCA
IC-718	TS-130S/V	FT-450 / FT-450D
IC-735 IC-736 / 738	TS-140s/680s	FT-480R FT-780R
IC-745	TS-430s	FT-747GX FT-757GX FT-767GX
IC-746 IC-746PRO	TS-440	FT-817 FT-818
IC-7400 IC-7410	TS-450S/690S	FT-847
IC-751A	TS-480	FT-857
IC-756PRO IC-756PROII IC-756PROIII	TS-530s	FT-890
IC-775 / DSP	TS-570D/G	FT-891
IC-781	TS-590S/590SG	FT-897
IC-7000	TS-790A/E	FT-920 FT-950
IC-7100 IC-7200	TS-830s	FT-990
IC-7300	TS-850s	FT-991 FT-991A
IC-7600	TS-870s	FT-1000
IC-7700	TS-930s	FT-1000MP Mark-V
	TS-940s
IC-R72	TS-950S/SD TS-950SDX	FT-1000MP Mark-V Field
IC-9100	TS-2000 – HF/50 MHz TS-2000 – VHF/UHF TS-2000 – ALL BANDS TS-2000X – 23 cm	FTDX-1200
IC-R7000 – use EXT IF IC-R8500 IC-R9000	R-2000 R-5000	FT-2000 FTDX-3000 – use IF OUT

Alinco DX-70TH/EH
CODAN 9360	JRC NRD-535
Collins KWM380	JRC NRD-525
President Jackson – Silver President Jackson II	Ranger RCI-2950 Ranger RCI-2970N2
President Grant	Galaxy DX 959

ATTENTION: Though installing the IFace is not difficult, you do this at your own risk. TSP S.r.l. is not responsible for any damage, unwanted side-effects or whatever.

If your radio is not yet listed in the table, send us the request and we will prepare the instructions as soon as possible.

December 19, 2018

CW Stick Keyer 2: new testimonial

By admin in Radio accessories Tag cw, ham radio, icom, keyer, morse, test

We publish a new testimonial about how to use our CW Stick Keyer 2 with desktop transceivers. In the video you can see that it works perfectly with the great ICOM IC-775.

Enjoy!

For more information please use the following form.

November 18, 2018

Morse Stick Keyer 2: how to use it!

By admin in News, Radio accessories Tag cw, ft-817, ham radio, keyer, morse, paddle, stick, telegraphy

A new video from TSP S.r.l. shows how to use the “Morse Stick Keyer 2”, the most light and small paddle for telegraphy of the world. The demostration is made using a well know YAESU FT-817. This paddle works very well with other radio too, for example with: FT450D, IC7000, IC7300, TS-480, KX3 and many more.

You can find all the information at the product page. Here below you can find the demo video (please activate the subtitles). Enjoy.

For more information please use the following form.

July 28, 2018

CW Stick Paddle 2

By admin in Products, Radio accessories Tag cw, ft-817, keyer, morse, paddle, radio, stick, telegraphy

CW Stick Paddle 2 is a simple and easy to use Morse code keyer thought to be light, small and inexpensive. With respect the previous version, this adds the squeeze mode feature.

It is ideal for portable and QRP operations, in car installations, but also for travelling everywhere you want with your favourite radio.

It doesn’t have mechanical parts, it is totally electronic. And it doesn’t need any battery to work! Use simply your fingers to start operating Morse code with your favourite radio.

It works with all the modern transceivers replacing a normal mechanical 3 wires Morse keyer.

It is available in two versions, the “standard” and the “Black & Gold Limited Edition”, elegant and beautiful !!!

It can be used with FT-450D, FT-817, FT-857, FT-897, IC-706, IC-7000, IC-7300, TS-480, Elecraft KX3, Mountain Topper Radio MTR3B and similar (low voltage (3 – 5 V) on keyer connector).

Technical data:

size – 100 x 19 x 3 mm;
weight – 6 grs + cable (tot. 30 grs);
cable – 60 cm 3 wire;
connector – 3,5 mm stereo jack.

Do you like it? Buy one (or more) by pressing one of the following buttons.

Want more information? Please read the FAQ (click here) or please watch these demo videos.

If you have questions please use the following form.

April 17, 2014

Morse Stick Keyer

By admin in Radio accessories Tag yaesu, cw, ft-817, hamradio, keyer, morse, paddle, radio, telegraphy

Morse Stick is a simple and easy to use Morse code electronic keyer thought to be light, small and inexpensive.

It is ideal for portable and QRP operations, in car installations, but also for travelling everywhere you want with your favourite radio.

It doesn’t have mechanical parts, it is totally electronic. And it doesn’t need any battery to work! Use simply your fingers to start operating Morse code with your favourite radio.

It works with all the modern transceivers replacing a normal mechanical 3 wires Morse keyer.

It can be used with FT-450D, FT-817, FT-857, FT-897, IC-706, IC-7000, IC-7300, TS-480, Elecraft KX3 and similar (low voltage (3 – 5 V) on keyer connector).

Technical data: